BACK TO HOME PAGE
1. IDENTIFICATION OF PRODUCT AND COMPANY
Product name : POLYWAX polymer wax rinse aid additive
Company : AMTEC Industries, 1 West End Units, Charlesfield Trading Estate,
St. Boswells, Melrose, TD6 0HH.
Tel: +44 (0)1835 823750, Fax: +44 (0)8707 052228
2. COMPOSITION/ HAZARDOUS INGREDIENTS
Ingredient name Cas No. Contents Classification
Nonionic detergent n/a <15% n/a
Amides, Coco, N-N-bis ethyl 68603-42-9 <5% Xi;R36/38
Polymer wax 5064-31-3 <5% n/a
On available data this preparation is not required to carry a hazard classification according
to EEC directives 88/379/EEC and 79/831/EEC.This product may cause soreness and irritation in contact with eyes.
Prolonged contact with skin may result in irritation.4. FIRST AID MEASURES
Exposure route Symptoms Treatment
Inhalation Mists may irritate the breathing passages, Remove from exposure, rest and keep warm. In severe cases or if recovery is not rapid or complete seek medical attention. Skin Contact Slight irritation. Drench the skin with plenty of clean water. Remove contaminated clothing and wash before reuse. If irritation persists seek medical attention. Eye contact Irritation. Irrigate thoroughly with water for at least 10 minutes. Obtain medical attention. Ingestion Irritation of the digestive tract. Wash out the mouth with water. Do not induce vomiting. If patient is conscious give water to drink. If patient feels unwell seek medical attention.5. FIRE FIGHTING MEASURES
This preparation is stable and non-combustible.
6. ACCIDENTAL RELEASE MEASURES
Safety precautions : Wear appropriate PPE - see section 8.
Environmental : Prevent entry into drains and water courses.
Clean up procedures : Spillage's should be contained using soil or other adsorbent material to
prevent contamination of drains and water courses. Waste from spillage's should be disposed of in
accordance to local regulations.
Spilled material may cause surfaces to become slippery.7. HANDLING AND STORAGE
Store securely in labeled containers.
Keep out of reach of children.
Protect from freezing8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Exposure controls : Respiratory protection is not normally required but if spraying applications are
involved in a confined area appropriate masks should be worn.Personal protection : Respiratory, wear a simple mask to prevent inhalation of liquid as a vapour.
Hands, the use of suitable PVC gloves is recommended.
Eyes, safety glasses or goggles, (BS2902).
Skin. Apron, overalls
Hygiene. Always wash thoroughly after handling chemicals.
9. PHYSICAL AND CHEMICAL PROPERTIES
State : Liquid
Colour : Pink
pH-value : 7
Boiling point : 100oC
Flash point : Aqueous solution, not flammable.
Solubility : Miscible in all proportions.
Density @ 25oC :
Odour : Slight characteristic.
10. STABILITY AND REACTIVITY
This product is stable in excess of one year when stored between 5 O C and 30OC.
11. TOXICOLOGICAL INFORMATION
Effects : Harmful if swallowed. Irritating to the eyes, may cause slight temporary irritation by all
other routes of exposure.12. ECOLOGICAL INFORMATION
Soluble in water, readily biodegradable. Do not release the concentrate into surface waters.
13. DISPOSAL CONSIDERATIONS
The product is not classified as hazardous waste.
Disposal of large quantities as waste must always comply with existing EEC, national and
local regulations. Registered waste carriers and licensed disposal sites must be used.14. Transport considerations
Not classified as hazardous for transportation according to international regulations.
15. REGULATORY INFORMATION
This preparation does not carry a hazard classification according to EEC directives
88/379/EEC, 67/548/EEC and 79/831/EEC.
16. OTHER INFORMATION
This material is usually used for washing traffic film from vehicles and for cleaning contaminated
hard surfaces.
The information contained in this data sheet does not constitute an assessment of workplace risks.